38.11.24 ADCANCON – ADC Analog Warm-up Control Register

This register contains the warm-up control settings for the analog and bias circuit of the ADC module.

Name:	ADCANCON
Offset:	0x1800
Reset:	0x00000000
Property:	-


Bit	31	30	29	28	27	26	25	24
					WKUPCLKCNT[3:0]
Access					R/W	R/W	R/W	R/W
Reset					0	0	0	0


Bit	23	22	21	20	19	18	17	16
	WKIEN7							WKIEN0
Access	R/W							R/W
Reset	0							0


Bit	15	14	13	12	11	10	9	8
	WKRDY7							WKRDY0
Access	R/HS/HC							R/HS/HC
Reset	0							0


Bit	7	6	5	4	3	2	1	0
	ANEN7							ANEN0
Access	R/W							R/W
Reset	0							0

Bits 27:24 – WKUPCLKCNT[3:0] Wake-up Clock Count bits

These bits represent the number of ADC clocks required to warm-up the ADC module before it can perform conversion. Although the clocks are specific to each ADC, the WKUPCLKCNT bit is common to all ADC modules.

Value	Description
1111	2¹⁵= 32,768 clocks
...
...
...
0110	2⁶= 64 clocks
0101	2⁵= 32 clocks
0100	2⁴= 16 clocks
0011	2⁴= 16 clocks
0010	2⁴= 16 clocks
0001	2⁴= 16 clocks
0000	2⁴= 16 clocks

Bit 23 – WKIEN7 Shared ADC (ADC2) Wake-up Interrupt Enable bit

Value	Description
1	Enable interrupt and generate interrupt when the WKRDY2 status bit is set
0	Disable interrupt

Bit 16 – WKIEN0 ADC1Wake-up Interrupt Enable bit

Value	Description
1	Enable interrupt and generate interrupt when the WKRDYx status bit is set
0	Disable interrupt

Bit 15 – WKRDY7 Shared ADC (ADC2) Wake-up Status bit

Note: This bit is cleared by hardware when the ANEN2 bit is cleared.

Value	Description
1	ADC2 Analog and bias circuitry ready after the wake-up count number 2^WKUPEXP clocks after setting ANEN2 to ‘`1`’
0	ADC2 Analog and bias circuitry is not ready

Bit 8 – WKRDY0 ADC1 Wake-up Status bit

Note: This bit is cleared by hardware when the ANENx bit is cleared.

Value	Description
1	ADC1 Analog and bias circuitry ready after the wake-up count number 2^WKUPEXP clocks after setting ANEN1 to ‘`1`’
0	ADC1 Analog and bias circuitry is not ready

Bit 7 – ANEN7 Shared ADC (ADC2) Analog and Bias Circuitry Enable bit

Value	Description
1	Analog and bias circuitry enabled. Once the analog and bias circuit is enabled, the ADC module needs a warm-up time, as defined by the WKUPCLKCNT[3:0] bits.
0	Analog and bias circuitry disabled

Bit 0 – ANEN0 ADC1 Analog and Bias Circuitry Enable bits

Value	Description
1	Analog and bias circuitry enabled. Once the analog and bias circuit is enabled, the ADC module needs a warm-up time, as defined by the WKUPCLKCNT[3:0] bits.
0	Analog and bias circuitry disabled