Introduction
1 Definitions, Acronyms and Abbreviations
2 Overall Description
3 Metrology Interface Definition
- 3.1 Metrology Control Registers
- 3.2 Metrology Status Registers
  - 3.2.1 Metrology Firmware Version
    Metrology Firmware Version
  - 3.2.2 Metrology Status Register
    Metrology Status Register
  - 3.2.3 Metrology State Flags Register
    Metrology State Flags Register
  - 3.2.4 Waveform Capture Function Status
    Waveform Capture Function Status
  - 3.2.5 Measurement Interval Number
    Measurement Interval Number
  - 3.2.6 Number of Samples in the Last Measurement Interval
    Number of Samples in the Last Measurement Interval
  - 3.2.7 Phase Correction Filter Offset
    Phase Correction Filter Offset
  - 3.2.8 Dominant Line Voltage Fundamental Harmonic Frequency
    Dominant Line Voltage Fundamental Harmonic Frequency
  - 3.2.9 Line Voltage Fundamental Harmonic Frequency
    Line Voltage Fundamental Harmonic Frequency
  - 3.2.10 Sensor Temperature
    Sensor Temperature
  - 3.2.11 Voltage Peak Registers
    Voltage Peak Registers
  - 3.2.12 Phase Current Peak Registers
    Phase Current Peak Registers
  - 3.2.13 Neutral Current Peak Registers
    Neutral Current Peak Registers
  - 3.2.14 Compiled Feature Indicator Bits
    Compiled Feature Indicator Bits
  - 3.2.15 Number of Samples in the Last Cycle
    Number of Samples in the Last Cycle
  - 3.2.16 Pulse Counters
    Pulse Counters
  - 3.2.17 Zero-Crossing Sample Number of Phase-X Voltage
    Zero-Crossing Sample Number of Phase-X Voltage
  - 3.2.18 ATSENSE Calibration Trim Data, Registers: 0x41 – 0x44
    ATSENSE Calibration Trim Data, Registers: 0x41 – 0x44
  - 3.2.19 ATSENSE Calibration Trim Data, Registers: 0x45 – 0x48
    ATSENSE Calibration Trim Data, Registers: 0x45 – 0x48
- 3.3 Accumulated Output Quantities
- 3.4 Per-Cycle Accumulated Output Quantities
- 3.5 Harmonic Analysis Output Quantities
- 3.6 Derived Output Quantities
4 Interface between Metrology and Application
5 Annex – Meter Forms
The service type determines what meter form is being implemented and how the Metrology DSP core interprets and processes the ADC values.
6 References
7 Revision History
Microchip Information

3.2.16 Pulse Counters

Name:	PULSEx_COUNTER
Property:	Read


Bit	31	30	29	28	27	26	25	24
	PULSEx_COUNTER[31:24]
Access	R	R	R	R	R	R	R	R
Reset	0	0	0	0	0	0	0	0


Bit	23	22	21	20	19	18	17	16
	PULSEx_COUNTER[23:16]
Access	R	R	R	R	R	R	R	R
Reset	0	0	0	0	0	0	0	0


Bit	15	14	13	12	11	10	9	8
	PULSEx_COUNTER[15:8]
Access	R	R	R	R	R	R	R	R
Reset	0	0	0	0	0	0	0	0


Bit	7	6	5	4	3	2	1	0
	PULSEx_COUNTER[7:0]
Access	R	R	R	R	R	R	R	R
Reset	0	0	0	0	0	0	0	0

Bits 31:0 – PULSEx_COUNTER[31:0] Pulse counters (uQ32.0)

The registers count the number of pulses generated by the available pulse outputs.

DS50003461F

The online versions of the documents are provided as a courtesy. Verify all content and data in the device’s PDF documentation found on the device product page.